What Size Air Conditioner Do I Need? Square Footage Calculator

12,000 BTU

An air conditioner’s size is measured in BTU per hour (or in tons, at 12,000 BTU each), and the quickest clue for choosing one is the square footage you want to cool. But it is only the starting point: bigger is not better, and square footage does not account for sun, insulation or climate. This calculator gives you an approximate figure and explains when a professional calculation is needed.

5,000 BTUFor a room of 100 to 150 square feet, according to ENERGY STAR
12,000 BTUFor one of 450 to 550 square feet (one ton)
1 ton per 500-600 sq ftRule of thumb for central air in the whole house
+4,000 BTUIf the room is a kitchen, according to ENERGY STAR

Calculate the size you need

––
––
––

For a room, use the ENERGY STAR table (8-foot ceiling) and its adjustments; the order in which they are applied is our own calculation. For the whole house, use the rule of 1 ton per 500 to 600 square feet and the PickHVAC table (both approximate; a ton is 12,000 BTU per hour). It does not replace an installer’s load calculation.

One room: the ENERGY STAR table

For window or portable units, ENERGY STAR publishes a table relating area to the capacity needed, assuming an 8-foot ceiling.

010,00020,00030,000Recommended capacity for a room (BTU per hour)100 to 150 sq ft5,000150 to 250 sq ft6,000250 to 300 sq ft7,000300 to 350 sq ft8,000350 to 400 sq ft9,000400 to 450 sq ft10,000450 to 550 sq ft12,000550 to 700 sq ft14,000700 to 1,000 sq ft18,0001,000 to 1,200 sq ft21,0001,200 to 1,400 sq ft23,0001,400 to 1,500 sq ft24,0001,500 to 2,000 sq ft30,0002,000 to 2,500 sq ft34,000With an 8-foot ceiling
ENERGY STAR table for room air conditioners.

The table is adjusted for the room: 10% less if it is very shaded, 10% more if it is very sunny, 600 BTU more for each person beyond the second and 4,000 BTU more if it is a kitchen. If the ceiling is higher than 8 feet, the source gives no numerical adjustment and suggests a unit with a higher air-cleaning capacity (CADR).

Source: ENERGY STAR, room air conditioners.

Whole house: tons

For central air, the most repeated rule is one ton for every 500 or 600 square feet, which is the one PickHVAC and others use. This PickHVAC table translates it by home size.

TonnageBTU per hourApproximate home (square feet)
1.5 t18,000600 to 900
2 t24,0001,000 to 1,300
2.5 t30,0001,300 to 1,600
3 t36,0001,600 to 1,900
3.5 t42,0001,900 to 2,200
4 t48,0002,200 to 2,600
5 t60,0002,600 to 3,200

Source: PickHVAC, air conditioner size and cost. These are the site’s own estimates.

The rule ignores insulation, windows, ceiling height, climate and air leaks, according to ServiceMag. An experienced installer estimates that, with the same layout, the cooling load of two cities like Santa Monica and Palm Springs can differ by 30% to 50%. It is a field estimate from that source, not a published figure, but it shows why square footage is not enough.

Two worked examples

A whole house. Using the one-ton-per-500-to-600-square-feet rule, an 1,800 square foot home works out to 3 to 3.6 tons, which falls in the 3-ton row of the PickHVAC table (1,600 to 1,900 square feet). That is only a starting point: a well-insulated house in a mild climate may need less, and a leaky one in a hot climate may need more, which is why a load calculation matters.

A single room. Start with the capacity from the ENERGY STAR table for the floor area. Then adjust: 10% more if the room is very sunny, 600 BTU more for each person beyond two, and 4,000 BTU more if it is a kitchen. For an illustrative room whose table value is 10,000 BTU, sunny and with four people, the adjustment is +1,000 and +1,200, giving about 12,200 BTU. Choose the unit closest to that, without going over by much.

Why bigger is not better

Humidity

Removes less moisture

According to ENERGY STAR, a unit that is too large cools the air before it can remove the moisture, and the room ends up damp and clammy.

Cycling

Short cycling

An oversized unit switches on and off frequently. Each start wears the equipment more than running continuously, according to Energy Vanguard.

Cost

Costs more and uses more

ENERGY STAR states that an oversized unit costs more to buy, wastes energy and does not cool better.

Energy Vanguard proposes a simple test with a stopwatch: if the air conditioner runs 10 minutes or less before shutting off, it is clearly oversized; 20 minutes is acceptable, and at 30 minutes or more humidity is usually low. Some dispute that oversizing causes that much humidity, so it is a clue, not a definitive test.

What a load calculation looks at

The most widely used professional calculation is called Manual J. According to ServiceMag, it takes into account the conditioned volume (not just the area), insulation, the size and orientation of the windows, air leaks, the heat from people and appliances, and the design temperatures for your climate. A basic calculation takes the installer between 45 and 90 minutes once they have the measurements. If the quote repeats the size of the previous unit, ask why.

How to tell that an air conditioner is the wrong size

Probably too big

It shuts off after 10 minutes or less, the air feels cold but clammy, and temperatures swing between starts.

Probably too small

It runs nearly all the time on hot days and never reaches the setpoint, even though the filters, coils and ducts are clean.

Energy Vanguard’s stopwatch test uses the same idea: 10 minutes or less of running means oversized, 20 is acceptable and 30 or more usually means humidity is under control. Try it on a hot day, and tell your installer what you found. For the cost of different sizes, see the air conditioner replacement calculator.

How to choose the size

  • Measure the square footage of what you want to cool and note the ceiling height, the sun exposure and how many people use the room.
  • For a room, use the calculator and look for a unit of that capacity, without going over.
  • For the whole house, use the figure as a clue and ask three installers to calculate the loads rather than repeat the previous unit.
  • If the unit shuts off in under 10 minutes, or the house feels damp, it may be oversized.
  • With the size settled, see what it costs in our air conditioner replacement cost calculator.
Does the number of floors matter?

Yes, because heat rises and the top floor often needs more cooling than the ground floor. A load calculation takes this into account; a simple rule does not.

Should I add capacity for a future addition?

Not by oversizing now. It is better to size for what you have and handle the addition when it happens, or ask about a system that can be expanded.

Is a mini-split sized the same way?

Each indoor unit is sized for its room or zone, and the outdoor unit for the total. See central air versus mini-split for the cost side.

Summing up

The right size comes from the house, not from a rule of thumb. Use square footage to get a first idea, test the result against the way the home behaves (the stopwatch test is simple), and ask a professional for a load calculation when the investment is large. A correctly sized unit costs less to buy, uses less energy and keeps the air more comfortable.

If this raised more questions, Air Conditioner Replacement Cost Calculator goes into more detail, and HVAC System Replacement Cost: What Drives the Price Up covers the next step.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top