How Much Insulation Do You Need? R-Value by Climate Zone

Zone 1R30+ Zone 2R49+ Zone 3R49+ Zone 4R60 Zone 5R60 Zone 6R60 Zone 7R60 Zone 8R60 The colder the climate, the more R-value in the attic (uninsulated attic, according to DOE)

How much insulation your home needs depends mostly on the climate zone. According to the Department of Energy (DOE), an uninsulated attic calls for R-30 to R-49 in zone 1 up to R-60 in the cold zones, and the floor from R-13 up to R-38. Find your zone, look at the table and use the calculator.

8 zonesClimate zones in the U.S. (1 warm, 8 very cold)
R30 to R60Uninsulated attic, by zone (DOE)
R13 to R38Uninsulated floor, by zone (DOE)
By countyThe zone is assigned by county, not by city

What R-value does the DOE recommend for you?

Attic (total R)–
Uninsulated floor–
Uninsulated wall–

The attic, floor and wall values are from the DOE (undated table citing the 2021 IECC). The inches are our own calculation: total R ÷ HomeGuide’s R per inch, taking the lowest R with the worst performance and the highest with the best. They are the total thickness, not what is left to add. With insulation already in place, the real thickness and R depend on its type and condition.

What R-value is

R-value measures a material’s resistance to heat flow: the higher, the better it insulates. It depends on the type of insulation, its thickness and its density, and can change with temperature, aging and moisture. When layers are stacked, their R-values add. Compressed insulation does not deliver its full R, and thermal bridges (heat passing through studs and joists) make a wall’s real R lower than that of the insulation alone (DOE).

How to find your climate zone

The U.S. is divided into eight IECC zones, from 1 (the warmest, which includes Hawaii and Puerto Rico) to 8 (the coldest). The DOE notes that zone 4 is split into “marine” and “non-marine”, and that Alaska is almost entirely zone 7, with some districts in zone 8. The zone is assigned by county, so confirm yours on the official map or with your builder.

City (county)IECC zone
Miami, Florida (Miami-Dade)1
Houston, Texas (Harris)2
Phoenix, Arizona (Maricopa)2
Atlanta, Georgia (Fulton)3
Chicago, Illinois (Cook)5
Boston, Massachusetts (Suffolk)5
Denver, Colorado (Denver)5
Minneapolis, Minnesota (Hennepin)6
Fairbanks, Alaska (Fairbanks North Star)8

Source: DOE, Building America: climate region guide (August 2015). The city-to-county match is ours, not the guide’s: verify it for your address.

Recommended R-value by zone

RegionUninsulated atticAttic with 3-4 in.Uninsulated floorUninsulated wallWall already insulated
1R30 to R49R19 to R38R13R13 or R0 + R10 CIN/A
2R49 to R60R38 to R49R13R13 or R0 + R10 CIN/A
3R49 to R60R38 to R49R19R20, or R13 + R5 CI, or R0 + R15 CIAdd R5 CI
4 (non-marine)R60R49R19R20 + R5 CI, or R13 + R10 CI, or R0 + R15 CIAdd R10 CI
4 marine and 5R60R49R30R20 + R5 CI, or R13 + R10 CI, or R0 + R15 CIAdd R10 CI
6R60R49R30R20 + R5 CI, or R13 + R10 CI, or R0 + R20 CIAdd R10 CI
7 and 8R60R49R38R20 + R5 CI, or R13 + R10 CI, or R0 + R20 CIAdd R10 CI

Source: DOE: Insulation (undated table; cites the 2021 IECC). CI is continuous insulation on the exterior of the wall, just under the siding. The table does not include values for crawl spaces or basements.

The attic: where it shows most

Recommended R-value in the uninsulated atticR-0R-20R-40R-60Zone 1R-30 to 49Zone 2R-49 to 60Zone 3R-49 to 60Zone 4 (non-marine)R-60Zones 4 marine and 5R-60Zone 6R-60Zones 7 and 8R-60
A single dot indicates a single value; a bar, a recommended range. Source: DOE, undated table.

The floor

Recommended R-value in an uninsulated floorR-0R-10R-20R-30R-40Zones 1 and 2R-13Zones 3 and 4 (non-marine)R-19Zones 4 marine, 5 and 6R-30Zones 7 and 8R-38
Zones 3 and 4 non-marine share R-19; zone 4 marine and 5 move to R-30 (DOE).

Walls: cavity plus continuous insulation

For walls, the DOE gives combinations: the R of the cavity between studs plus continuous exterior insulation (for example, R20 + R5 CI). In zones 1 and 2, R13 in the cavity or R10 of continuous insulation is enough; in cold climates continuous insulation of R5 to R20 is called for depending on the combination. If the wall is already insulated, the table indicates how much continuous insulation to add, and it does not apply in zones 1 and 2.

Working out what you have now

Measure the depth of the insulation and multiply by its R-value per inch. Bob Vila gives up to R-3.8 per inch for fiberglass, so 10 inches of fiberglass is at most around R-38, which is the ENERGY STAR level of R-38 for 10 to 14 inches in most attics. Compare your result with the column for your zone. If you have 3 to 4 inches, use the second column in the table. If the insulation is compressed, wet, uneven or full of gaps, it will perform below its label.

More is not always better

Each extra inch adds less than the one before it, because the heat you are already blocking is a smaller and smaller share of what is left. That is why the recommendations stop at certain values, and why going far above them rarely pays. Local codes can ask for more than the DOE table, as HomeGuide warns, so check yours.

How to use these values

  1. Look up your county and your climate zone.
  2. Measure how much insulation you have today (the attic is usually the easiest) and if it is 3 to 4 inches, use that column.
  3. Tackle the attic first: it is the easiest space to improve. Then the floor and walls.
  4. With the calculator, see how many inches each material needs; compare with the free space.
  5. Ask for three quotes that state the final R-value in writing; here is the comparison of materials.

Where to put the money first

The attic is usually the cheapest place to add R-value, and sealing air leaks before you insulate is the best first step. After that, floors over unconditioned spaces and then walls come next, because walls are the hardest to improve in an existing house. For a price on the attic, use the attic insulation calculator, and for walls, what it costs to insulate existing walls.

How do I find my climate zone?

Look up your county in the DOE guide or the ENERGY STAR map. Our city table is only an example, and the city-to-county match is ours, so verify it for your address.

Is the R-value on the bag the R-value I will get?

Only when it is installed to the label’s thickness and density. Compression, gaps and moisture reduce it.

Does a higher R-value always mean lower bills?

It helps, but air leaks, windows, ducts and equipment also matter. See how the materials compare and our savings calculator to rank upgrades.

Putting it into practice

Find your zone, measure what you have, compare it with the table and start with the attic. If you are far below the recommended value, insulation is one of the most cost-effective upgrades available, and sealing air leaks first will make it work better. If you are close to the recommendation, the gain from adding more is small, and your money may do more elsewhere. Remember that local codes can ask for more than the national table, so check them before you buy.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top