Insulating the walls of an existing home costs, according to HomeGuide, $1 to $5 per sq ft installed, and Angi gives $1.75 to $3.50 per sq ft for blown-in insulation in existing walls. For a 2,000 sq ft house, HomeGuide cites $1,700 to $8,500 for the exterior walls. There is no single figure: it depends on the method, the siding and how many holes have to be opened and repaired.
How much would it cost to insulate your walls?
Our own calculation: area × price per sq ft from each source. “Own calculation” for HomeGuide adds material and labor (blown-in $1.25 to $2.50 and foam $1.00 to $2.50, plus $0.25 to $2.50 for labor). The 1,500 sq ft is an example: count only the exterior walls, without windows or doors. It does not include repairing and painting the holes.
How closed walls are insulated
In a finished wall you cannot put in a fiberglass batt: the cavity between studs is filled through holes. A contractor describes the process on walls with siding: remove a row of siding, drill a hole in each cavity, fill and plug the holes; with brick, it is drilled in the mortar joint. This is information from a company that sells these services (RetroFoam, June 2024).
| Method | How it is done | Material (HomeGuide) | Notes |
|---|---|---|---|
| Blown-in (cellulose or fiberglass) | 1-inch holes are drilled in the drywall or siding and the insulation is blown in | $1.25 to $2.50 per sq ft | The simplest option for closed walls (HomeGuide) |
| Injection foam | Also through holes; injected as liquid foam | $1.00 to $2.50 per sq ft | “Premium” option (HomeGuide); creates an air seal that saves energy |
| Rigid foam | Installed from the outside, under the siding | $0.75 to $2.00 per sq ft | Not for closed cavities: it goes with siding work (HomeGuide) |
Sources: HomeGuide (undated) and RetroFoam of Michigan (June 12, 2024, contractor). HomeGuide notes that the cost of repairing the holes depends on how many there are and that some contractors include it.
What it costs per sq ft
Sources: HomeGuide and Angi. For material alone, Angi gives $0.50 to $1.10 for fiberglass, $0.60 to $1.80 for wet-spray cellulose and $2.00 to $2.30 for dense-pack cellulose.
What can raise or lower the cost
- How many holes have to be opened and repaired: it affects the final price (HomeGuide).
- Siding type and number of stories: they also matter, according to the contractor consulted.
- Insulation chosen: foam is presented as a “premium” option versus blown-in.
- Hidden hazards: a good contractor detects mold and electrical risks; asbestos must be removed by a professional in most areas (HomeGuide).
Reading the price range
HomeGuide’s $1 to $5 per square foot and Angi’s $1.75 to $3.50 for blown-in insulation overlap, but they are not measuring the same thing. One includes different materials and the cost of closing the holes; the other is specific to one method. For a 2,000 square foot house, a rough exterior wall area is a fraction of the floor area times the wall height, and the real number depends on windows, doors and gables. Ask the contractor to measure and write the square footage in the quote, so that you can check their price per square foot yourself.
Also ask what is included in the figure: drilling, filling, plugging, repairing drywall or siding, and cleaning up. Patching and repainting are the items that most often show up as extras.
What R-value you need
HomeGuide indicates a minimum of R-13 to R-21 depending on the climate and warns that local codes may require more. To see the DOE recommendation by zone, see our article on R-value by climate zone. None of the sources quantifies the energy savings of insulating existing walls, so we do not give a figure.
Find out what is already in the wall
Older homes often have some insulation already, or none at all, and the answer changes the quote. There are a few ways to find out without opening everything. An energy audit, which HomeGuide prices at $200 to $600, may include thermal imaging that shows where the walls are cold. A contractor can drill one small hole and look inside, and a handyman can sometimes check behind an outlet box. If you try that yourself, switch off the breaker for that circuit first, and do not touch anything you are not sure about.
Knowing what is there matters because partially filled walls, settled material and old products that you would not want to disturb are all things a contractor should tell you about before they start, not after.
Walls are rarely the first place to look
Insulating existing walls is one of the costlier upgrades per square foot of work, because the walls are closed and each cavity has to be reached. For many homes the best return comes first from sealing air leaks and adding attic insulation, which is cheaper and easier. Our attic insulation calculator shows what that typically costs, and the R-value by climate zone guide tells you how much you need. Walls come into their own when the attic is done and you are still cold, or when you are already opening them for other work.
Incentives and credits
HomeGuide mentions a 30% federal credit for insulation, but the IRS says the credit for efficiency improvements only covers what was installed before December 31, 2025 (page reviewed April 28, 2026). If you insulate today, do not count on it; look into local and utility incentives. Source: IRS.
What to do next
- Find out how many sq ft of exterior wall you have and whether they already have some insulation.
- Consider an energy audit ($200 to $600 according to HomeGuide) to see where you lose the most heat.
- Ask for at least three written quotes that include the material, the final R-value, hole repair and the finish.
- Ask how they detect mold, wiring and asbestos before starting.
- Compare with cheaper improvements, such as insulating the attic or sealing leaks.
Can I do it myself?
Renting a blower is possible for loose-fill products, but finding every cavity, working around wiring and blocking, and patching the holes make wall work harder than it looks. Many homeowners hire a contractor for closed walls.
Will blown-in insulation settle?
Loose materials can settle if they are not packed correctly, which is why the sources mention dense-pack cellulose. Ask the contractor how they ensure the cavity is filled, and whether they check the result.
Is moisture a concern?
It can be. Insulating a wall changes how it dries, so walls with existing leaks or rot should be fixed first. Ask the contractor about the wall type, the siding and any moisture problems before choosing a material.
If this raised more questions, How Much Insulation Do You Need? R-Value by Climate Zone goes into more detail, and Spray Foam, Fiberglass or Cellulose: Insulation Compared covers the next step.
